A file with spot UV varnish or foil stamping (metallic or holographic foil) is print-ready when it meets these conditions:
- Each finish goes on its own layer, with a spot colour of the same name: ‘Barniz’ (varnish) or ‘Stamping’ (foil stamping).
- Everything on that layer is vector, at 100% of the spot colour and set to overprint. No gradients, transparencies or screens.
- Positive text is at least 8 pt sans-serif and 10 pt serif with lamination. Without lamination, on holographic foil and when reversed out, larger.
- Lines are 0.25 mm to 0.7 mm at minimum, depending on the finish. That is millimetres, not points.
- No finish closer than 3 mm to the trim or the crease, and 3 mm between two different finishes.
- Raised varnish does not sit in the same place on the front and the back, and never overlaps the foil.
- The type of finish (flat or raised varnish; gold, silver, copper or holographic foil) is specified when you order, not in the file.
The rest of the file follows the usual rules: bleed, CMYK, resolution and fonts. They are in the guide How to prepare a file for printing. Here we only explain what changes when the piece has varnish or foil stamping.
1. How do you show in the file where the varnish or foil goes?
With a separate layer and a dedicated spot colour for each finish. Varnish and foil are not printed with ink: they are applied on top of the printed piece. That is why the file has to state, with an exact shape, where each one goes.
- One layer per finish. Name it ‘Barniz’ or ‘Stamping’. If the piece is die-cut or creased, those also go on their own layers: ‘Corte’ (cut) and ‘Hendido’ (crease).
- A spot colour with the same name as the layer. Everything on the ‘Barniz’ layer is filled with the ‘Barniz’ spot colour, and the same goes for ‘Stamping’. The colour it shows on screen does not matter: pick one that stands out clearly from the design.
- The type is specified when you order. The file says where the finish goes; whether the varnish is flat or raised, or whether the foil is gold, silver, copper or holographic, you tell us in the order.
If the varnish or foil has to match a printed element, such as a logo, copy its path and paste it onto the finish layer in the same position. If you redraw it by hand, it never quite matches.
What can go on the layer
- Vectors only: shapes, paths and text. A pixel image comes out with jagged edges.
- Always at 100% of the spot colour. Varnish and foil have no halftones: they are either there or not. A 50% tint turns into a dot screen and the result is unpredictable.
- No gradients, transparencies, shadows or effects. For the same reason.
What effect does each finish give? Spot UV varnish is a translucent gloss that lets the colour underneath show through. It stands out most on dark backgrounds or large areas of solid colour, and on matt or soft touch lamination; on white paper it is barely noticeable. Raised varnish adds volume and works for textures. Foil, on the other hand, covers: it leaves an opaque metallic or holographic film. We show this with photos in Finishes.
2. Why do varnish and foil have to be set to overprint?
Because otherwise the colour underneath disappears. By default, when one object sits on top of another, the software removes the one underneath (a ‘knockout’). For a colour in the design, that is correct. For a finish, it is not: varnish is applied on top of the print, so under the varnish shape you would be left with bare white paper.
Set the objects on the ‘Barniz’ and ‘Stamping’ layers to overprint fill and, if they have an outline, also overprint stroke. In section 7 we explain where to turn it on and how to check it.
Do not confuse these spot colours with the Pantone colours in the design. ‘Barniz’ and ‘Stamping’ are instructions for the finish and are never converted to CMYK. A Pantone in the design, on the other hand, is usually printed in four-colour process.
3. What minimum size do text and lines need?
It depends on the finish, on whether there is lamination underneath and on whether the element is positive or reversed out. With lamination, positive text needs at least 8 pt sans-serif and 10 pt serif; without lamination, 10 and 12 pt.
- Positive: the text or line carries the finish. For example, a logo in varnish on a matt background.
- Reversed out: the finish covers an area and the text is knocked out of it, with no finish. For example, a name in the background colour inside a patch of foil. It needs a much larger size, because the finish tends to fill in the gaps.
Text size is given in points (pt). Line weight and the spacing between elements are given in millimetres: 0.25 mm is almost three times the minimum print line (0.25 pt).
Positive elements
| Finish | Lamination underneath | Minimum text (sans-serif / serif) | Minimum line | Minimum spacing |
|---|---|---|---|---|
| Flat varnish | Yes | 8 / 10 pt | 0.25 mm | 0.25 mm |
| Flat varnish | No | 10 / 12 pt | 0.4 mm | 0.4 mm |
| Raised varnish | Yes | 8 / 10 pt | 0.35 mm | 0.35 mm |
| Raised varnish | No | 10 / 12 pt | 0.5 mm | 0.5 mm |
| Metallic foil | Yes | 8 / 10 pt | 0.5 mm | 0.35 mm |
| Metallic foil | No | 10 / 12 pt | 0.7 mm | 0.5 mm |
| Holographic foil | Yes | 9 / 11 pt | 0.5 mm | 0.35 mm |
Reversed-out elements (knocked out of the finish)
| Finish | Lamination underneath | Minimum text (sans-serif / serif) | Minimum line | Minimum spacing |
|---|---|---|---|---|
| Flat varnish | Yes | 14 / 18 pt | 0.35 mm | 0.35 mm |
| Flat varnish | No | 16 / 20 pt | 0.5 mm | 0.5 mm |
| Raised varnish | Yes | 14 / 18 pt | 0.5 mm | 0.5 mm |
| Raised varnish | No | 16 / 20 pt | 0.7 mm | 0.7 mm |
| Metallic foil | Yes | 14 / 18 pt | 0.5 mm | 0.5 mm |
| Metallic foil | No | 16 / 20 pt | 0.7 mm | 0.7 mm |
| Holographic foil | Yes | 18 / 20 pt | 0.6 mm | 0.35 mm |
For holographic foil without lamination, ask us before you design.
Point size is not enough: check the stroke too. Letters have to respect the minimum line. A light or thin typeface at 12 pt can have strokes finer than 0.35 mm, and those strokes break up or do not transfer. For text with a finish, use regular or heavier weights.
Example. A 7 pt legal notice in varnish will not work: with lamination, the minimum is 8 pt sans-serif. Nor will a 12 pt slogan knocked out of a patch of foil: reversed out, it needs 14 pt sans-serif with lamination, or 16 pt without.
4. How far from the trim, the crease and other finishes?
At least 3 mm, in all three cases.
- From the trim: no finish closer than 3 mm. The cut can shift by ±1 mm, and a finish right up against the edge can end up cut off or peel away.
- From the crease and the fold: no finish closer than 3 mm. When folded, varnish and foil crack or peel away. If the piece is folded, we explain this in the guide to folded leaflets.
- Between two different finishes: 3 mm apart. Raised varnish and foil never overlap.
Unlike the print, varnish and foil have no bleed: they stay inside the piece.
5. Can varnish or foil go on both sides?
Yes, but raised varnish cannot be in the same place on the front and the back. If it lines up, the raised area on one side affects the drying and the cutting of the other.
- Prepare the front and the back as separate pages of the same PDF, each with its own finish layer.
- Before you finalise the design, overlay the two pages and check that the raised elements do not line up. If they do, move one of them.
- Bear in mind that when you turn the piece over, what is on the left on the front ends up on the right on the back.
6. Do you need lamination under the varnish or foil?
Not always, but it is advisable. Varnish and foil adhere better to a laminated surface, which is why the minimums in the table are lower when there is lamination.
- Adhesion. On lamination, the finish adheres evenly. Without it, a lot depends on the paper.
- Detail. With lamination, text and lines can be finer (section 3).
- Contrast. Gloss varnish on matt or soft touch lamination gives the strongest contrast: you can see it and feel it.
- Paper. The paper has to accept lamination. Textured or very porous papers do not take varnish.
If your piece is not laminated, use the ‘No’ rows of the table and ask us about the paper first. For holographic foil, always ask us if there is no lamination.
7. How do I check the file before exporting it?
With the separations preview: if each finish appears as its own plate and, when you hide it, the design underneath is still intact, the file is correct.
In Illustrator
- Create the spot colour: in the Swatches panel, New Swatch, with Color Type: Spot Color and the name ‘Barniz’ or ‘Stamping’. Adobe’s name for a spot colour is ‘Spot Color’.
- In Window → Layers, create a layer with the same name and put the finish shapes on it, filled with that swatch at 100%.
- Select those shapes and, in Window → Attributes, turn on Overprint Fill (and Overprint Stroke if they have an outline).
- Convert the finish text to outlines with Type → Create Outlines.
- Open Window → Separations Preview and turn on Overprint Preview. Check that the ‘Barniz’ or ‘Stamping’ ink appears alongside the four CMYK inks, and that when you hide it the colour underneath is still complete, with no white gaps.
In InDesign
- Create the spot colour in the Swatches panel with New Color Swatch, Color Type: Spot and the same name as the layer.
- Create the layer in Window → Layers and place the finish shapes on it. If they come from Illustrator, the spot colour is kept when you place them.
- Turn on overprint in Window → Output → Attributes: Overprint Fill and, if needed, Overprint Stroke.
- In Window → Output → Separations Preview, check that the finish ink appears as its own plate and that there are no gaps underneath.
- Open the Ink Manager from the Swatches panel menu and check that there are no duplicate inks with similar names (‘Barniz’, ‘Barniz 2’, ‘barniz’).
If you design in Canva: Canva does not let you create spot colours or technical layers (we cover this in the file preparation guide). Send us the design and tell us where the finish goes; we will work out with you how to prepare those layers from it.
8. How do I export the PDF so it keeps the spot colours?
Export without converting the spot colours to four-colour process and with overprint left intact. Ask us which PDF/X standard to use: for jobs with special inks, it depends on the job.
- Export as an Adobe PDF for print: in InDesign, File → Export → Adobe PDF (Print); in Illustrator, File → Save As → Adobe PDF.
- Marks and bleed: turn on crop marks and 3 mm of bleed, as for any other job.
- Spot colours: in the Ink Manager in the export dialog, leave All Spots to Process turned off. If it is on, the varnish and foil are printed as just another colour.
- One PDF per product: with the front and the back as pages, in order.
After exporting, open the PDF in Acrobat and check the Output Preview: the ‘Barniz’ or ‘Stamping’ ink has to appear in the list, separate from CMYK.
9. What are the most common mistakes?
| Mistake | What happens | How to avoid it |
|---|---|---|
| The finish is not set to overprint | Bare white paper is left under the varnish or foil | Overprint fill and stroke; check with the separations preview |
| The finish is in a CMYK colour or a Pantone | It prints as just another colour and nobody can tell where the finish goes | A spot colour named ‘Barniz’ or ‘Stamping’ |
| Gradients, shadows, transparencies or screens on the layer | The finish has no halftones: it is lost or comes out with a ragged edge | Flat shapes at 100% |
| Small text or light typefaces | The letters fill in or break up | Respect the minimums in section 3, including stroke weight |
| Finish right up against the trim or over a fold | It gets cut off or peels away; on the fold it cracks | At least 3 mm from the trim and the crease |
| Raised varnish in the same place on the front and back | Drying and cutting problems | Move the raised elements on one of the sides |
| Finish made from a pixel image | Jagged edges | Vectors only; text converted to outlines |
| Hidden layers or leftover tests on the finish layer | Finishes appear where they should not | Check every layer before exporting |
Frequently asked questions
What is the difference between spot UV varnish and UV printing?
Spot UV varnish is a finish applied to a piece that has already been printed, on specific areas or over the whole surface. UV printing is a printing system, common in large format and on rigid substrates. This guide is about the varnish.
Where do I specify whether the varnish is flat or raised, or whether the foil is gold or silver?
When you order the job, not in the file. The file only says where each finish goes, with the ‘Barniz’ or ‘Stamping’ layer and spot colour.
Can I varnish the whole side of the piece?
Spot varnish works precisely because of the contrast with the unvarnished areas. If the finish is going to cover almost the whole side, ask us before you design.
Does varnish show up on a white background?
Barely. Varnish is translucent: it stands out on dark or very colourful backgrounds, and on matt or soft touch lamination. If the background is white, consider another finish or a coloured background.
Can I put varnish on a photo?
Yes, on the whole photo or part of it, as long as the varnish shape is a vector path. If you only want to varnish one object in the photo, its outline has to be drawn.
What if my file does not have the layers set up?
We check its technical specifications before production. If the finish layer is missing or not properly defined, we tell you what is missing and work out with you how to fix it.