A file with a die line is ready for print when it meets these conditions:
- Before drawing a new shape, ask which standard dies are available.
- The cut line goes on its own layer, with a spot colour of the same name: “Corte” (cut). Folds go on another: “Hendido” (crease).
- The line is a vector path with no fill, set to overprint. If it is a cutting shape, it is closed. It is not printed.
- The design has 3 mm of bleed all around the shape, including inside windows.
- Text and logos sit 3-5 mm from the line. The cut can shift by ±1 mm, so no frames hugging the edge.
- Two die lines are at least 2 mm apart.
- Each die-cut shape is sent as a single piece, at actual size, not imposed on a sheet.
The rest of the file follows the usual rules: CMYK, resolution and fonts. They are in the guide How to prepare a file for printing. Here we only explain what changes when the piece is die-cut.
1. What is a die and when do you need one?
A die is the form that cuts the piece along an outline that is not a rectangle. You need one whenever the piece does not end in four straight cuts.
- Custom shapes: a card with the profile of a product, a swing tag, a sticker with the outline of the logo.
- Rounded corners: on cards, correspondence cards or folders.
- Windows and cut-outs: an opening that shows what is underneath, as on a cover or a two-layer card.
- Pieces that fold or are assembled: presentation folders with pocket and flaps, door hangers, shaped leaflets.
- Labels and stickers: the shape of each label is cut without cutting the backing paper behind it.
2. Are there standard dies, or does a new one have to be designed?
There are standard dies: ask which are available before designing a new one. The shape you are after may already exist.
- If your shape fits an existing one, there is no need to draw or check a shape from scratch: you design on that outline.
- If you need a custom shape, you draw it yourself following this guide. The sooner you show it to us, the sooner you will know whether any detail needs adjusting: corners, distances or windows that are too narrow.
Either way, finalise the shape before laying out the design. If the outline changes at the end, bleed, margins and text all have to be checked again.
3. How do you draw the die line in the file?
On a separate layer and with its own spot colour for each type of line, in exactly the position it takes over the design and at actual size.
- One layer per type of line. “Corte” for the outline and windows; “Hendido” for folds. If the piece has a kiss cut or perforation, each goes on its own layer, with a name that says clearly what it is: “Medio corte” (kiss cut), “Perforado” (perforation).
- A spot colour with the same name as the layer. Everything on the “Corte” layer is drawn with the “Corte” spot colour. The colour it shows on screen does not matter: pick one that stands out clearly from the design.
- In the same file and on the same page as the design. Not in a separate PDF or on the next page: the line has to match the design to the millimetre.
Types of line
| Line | What it does | Layer and spot colour | Example |
|---|---|---|---|
| Cut | Cuts right through the material | “Corte” | Outline of a card, window in a cover |
| Crease | Marks the fold without cutting, so it folds cleanly | “Hendido” | Flaps of a folder, fold of a correspondence card |
| Kiss cut | Cuts only the top layer | “Medio corte” | Sticker sheets: the label is cut, not the backing paper |
| Perforation | A line of short cuts for tearing off by hand | “Perforado” | Coupon or stub that is torn off |
Creasing is essential on board: from 170 g upwards, folding without creasing cracks the paper. If your piece is a leaflet, the size of each panel and the page order are in the guide to folded leaflets.
4. What should the line's path be like?
Vector, stroke only, at 100 % of its spot colour and set to overprint. That way it shows on screen, separates from the design and is not printed.
- Vectors only. An outline taken from a pixel image cannot be followed accurately.
- Closed cutting shapes. The outline of a piece or a window starts and ends at the same point, with no gaps. An open shape leaves the piece attached to the rest of the material. Crease and perforation lines, on the other hand, are open lines: they run from one point to another.
- One path per line. No duplicated lines on top of each other and no overlapping segments: a repeated line gets cut twice.
- No fill, at 100 % of the spot colour. A thin, continuous stroke, with no hand-drawn dashes: the perforation is already indicated by its layer.
- Set to overprint. Mark the line with Overprint Stroke. Otherwise the software knocks out the design underneath and, once the line is removed, a thin white line is left exactly where it is cut.
If the shape has to follow an element of the design, such as the outline of a logo, copy its path, paste it onto the “Corte” layer in the same position and offset it outwards as far as you need. If you redraw it by hand, it never matches exactly.
5. How much bleed does a die-cut piece need?
3 mm all around the shape, just as with a straight cut. The background, photo or colour that reaches the edge of the shape has to continue 3 mm beyond the cut line.
- All around the outline, including curves and recesses. A rectangle of bleed around the piece is not enough if the shape has protrusions.
- In interior windows, into the opening. If the edge of the window has colour, that colour extends 3 mm into the area that will be removed.
- With crop marks in the PDF, as for any other job.
The reason is the same as we explain in the file preparation guide: no cut falls exactly on the theoretical line. Without bleed, any deviation leaves a thin white line on the edge of the shape.
6. How far from the line should text and frames be?
Text, logos and important details, 3-5 mm from the cut line. The cut can shift by ±1 mm.
- Nothing important next to the line. Text, logos, QR codes and contact details, inside the safe area. Also next to windows and creases.
- Frames and borders, well away from the cut. A frame that follows the outline closely shows up any shift. If you draw it 2 mm from the edge and the cut moves 1 mm, it will end up 1 mm away on one side and 3 mm on the other: it looks crooked. If you want a frame, give it a generous margin or do without it.
- Die lines at least 2 mm apart. For example, between two windows or between a window and the outline. If they are closer, the strip of material left in between tears or warps.
- Finishes 3 mm from the cut and the crease. If the piece has varnish or foil stamping, we explain it in the guide to spot UV varnish and foil stamping.
Example. On a swing tag with a drilled hole at the top, the text cannot sit 1 mm from the hole or from the outline: keep it 3-5 mm from both. And between the hole and the edge of the tag, at least 2 mm of material.
7. What is the difference between a steel-rule die, laser cutting and a plotter?
The file is prepared the same way whatever the technique: a “Corte” line on its own layer. What changes is which shapes and how much detail each technique can handle, and it is worth knowing that before you design.
| Technique | How it cuts | What to bear in mind |
|---|---|---|
| Steel-rule die | A blade in the exact shape presses on the piece and cuts it in one go | Very fine details and very tight inside corners have limits |
| Laser cutting | A beam of light follows the line and burns the material | Handles free shapes and fine detail; on light-coloured papers it can leave the edge slightly scorched |
| Cutting plotter | A small blade follows the line, like a pencil | Handles free shapes; common for stickers and vinyl |
| CNC routing | A rotating router bit follows the line | For rigid substrates; inside corners are left with a small radius |
If a particular detail matters for your piece, such as an edge with no trace of scorching or a very narrow window, tell us when you order and we will work out with you which technique suits it.
8. How do you prepare a shaped cut in large format?
With the same “Corte” layer, but with the material in mind. Flexible substrates and cardboard are cut with a blade; rigid ones, such as acrylic, foam PVC or aluminium composite, with a router.
- Inside corners with a small radius. The router bit is round and cannot make a perfectly square inside corner. If you draw a sharp inward angle, it will come out slightly rounded. Draw it with a small radius from the start and you will see on screen what you are going to get.
- Bleed and margins: in large format they depend on the substrate and how it is fixed. Ask us before finalising the design; we explain this in the file preparation guide.
9. How do I check the file before exporting it?
With the separations preview: if the “Corte” line comes out as a plate of its own and hiding it leaves the design underneath intact, the file is fine.
In Illustrator
- Create the spot colour: in the Swatches panel, New Swatch, with Color Type: Spot Color and the name “Corte”. Repeat with “Hendido” and any other lines the piece has.
- In Window → Layers, create a layer with the same name and draw the line on it, with a stroke in that swatch at 100 % and no fill.
- Select the line and, in Window → Attributes, turn on Overprint Stroke.
- Open Window → Separations Preview and turn on Overprint Preview. Check that the “Corte” ink appears alongside the four CMYK inks, and that hiding it leaves no white gap in the design.
- Hide the design layer and look at the “Corte” layer on its own: closed shapes, no duplicated lines and no leftover test marks.
In InDesign
- The most reliable approach is to draw the die line in Illustrator and place it in InDesign, on its own layer and in the same position over the design. The spot colour is preserved when you place it.
- Check in Window → Output → Separations Preview that the “Corte” ink appears as a plate of its own.
- Open the Ink Manager from the Swatches panel menu and check that there are no duplicate inks with similar names (“Corte”, “Corte 2”, “corte”).
When exporting, do not convert spot colours to process: if they are converted, the cut line prints as just another colour. The steps are the same as for varnish; they are in the varnish and foil stamping guide.
If you design in Canva: Canva cannot create the die-line layer (we explain this in the file preparation guide). Send us the design with bleed and tell us the shape; we will work out with you how to prepare that layer from it.
10. What are the most common mistakes?
| Mistake | What happens | How to avoid it |
|---|---|---|
| The cut line is in a CMYK colour | It prints and cannot be told apart from the design | A “Corte” spot colour on its own layer |
| The line is not set to overprint | A thin white line exactly where it is cut | Overprint Stroke; check with the separations preview |
| Open cutting shape or duplicated lines | The piece does not come away, or is cut twice in the same place | One closed path per shape |
| No bleed around the shape | White edge on the outline or in the windows | 3 mm of bleed all around the outline, including into the windows |
| Text or logo right up against the line | The cut grazes or cuts it | 3-5 mm safe area |
| Frame following the outline very closely | With a ±1 mm shift it looks crooked | Generous margin or no frame |
| Die lines less than 2 mm apart | The strip of material between them tears | Keep them at least 2 mm apart |
| Cut and crease on the same layer | There is no telling which line cuts and which folds | One layer and one spot colour per type of line |
| Sharp inside corner on a rigid substrate | It comes out rounded | Draw it with a small radius from the start |
Frequently asked questions
Can I put several different shapes in the same file?
Not as an imposed sheet: each die-cut shape is a piece. Send each shape in its own file or on its own page, at actual size and with its “Corte” layer. If the product is a sticker sheet with several shapes, the sheet is the piece: the outer cut goes on “Corte” and the labels on “Medio corte”.
How thick should I draw the die line?
Thin and even: the thickness is only there so you can see it on screen. What matters is that it is a vector path in its spot colour and set to overprint.
Is the die line printed?
No. It shows where the piece is cut, folded or perforated. That is why it goes in its own spot colour and set to overprint: that way it separates from the design without leaving gaps in it.
Where do I say whether the cut is done with a die, a laser or a plotter?
When you order the job, not in the file. The file only says where to cut, with the “Corte” layer and spot colour.
Can I put a window very close to the edge of the piece?
Leave at least 2 mm of material between the window and the outline. Any less and that strip tears or warps when the piece is cut or handled.
What happens if my file has no die-line layer?
Before production we check its technical specifications. If the cut layer is missing or not properly defined, we tell you what is missing and work out with you how to solve it.